skip to main content

→ Top Stories:
Fracking
Safe Chemicals
Defending the Clean Air Act

Ed Osann’s Blog

Waiting for Hot Water

Ed Osann

Posted January 22, 2014 in Living Sustainably

Tags:
, , , , , , , ,
Share | | |

Shower Head with Droplets Close Up.jpgWe all do it, nearly every day.  We turn on the shower and wait.  And wait.  Maybe we brush our teeth while waiting, or go start the coffee, or take clothes out of the closet, or fold some laundry.  20 seconds, 30 seconds, 40 seconds, a full minute – waiting for hot water before we step into the shower.

How long do you wait for hot water?  Take our web poll at the bottom of this post.

In a 2009 modeling study, researchers estimated that over 10% of all the hot water drawn for showering in a typical single-family home is wasted waiting for hot water to arrive.  With Americans taking over 200 million showers a day, that’s a lot of water and energy literally down the drain, of no benefit to anyone.  Using EPA estimates of shower water use, that’s about 280 million gallons of hot water wasted each day -- water that has been heated by a water heater, but then allowed to cool as it sits in long pipe runs that are not insulated. This amount of hot water is greater than the total amount of all water used on an average day in the city of Philadelphia, the nation’s fifth-largest.  And the energy used to heat this wasted hot water results in annual greenhouse gas emissions equal to that of 1.6 million passenger vehicles.  And that’s not even counting the additional water that gets wasted while waiting for hot water to arrive at a lavatory faucet or the kitchen sink.

And the wait isn’t necessarily shorter in new homes.  As homes grew bigger during the housing bubble, floor plans expanded, piping was extended, and wait times grew even longer.  Additionally, although the flow rates for new faucets and showers have come down over the last 20 years in response to state and federal efficiency standards, designers often neglect to downsize the pipes serving these more efficient fixtures.  This leaves an unnecessarily large amount of water siting in the hot water pipes cooling off between uses, resulting in longer wait times for hot water to arrive at the beginning of the next use.  According to at least one industry insider, one of the top complaints of new home buyers in recent years has been too much time waiting for hot water.

As the housing market rebounds, the efficiency of new homes will only grow in importance.  For the last two years, NRDC has been working to reduce the wait for hot water – and the resulting waste of water and energy -- in new homes by working for changes in building and plumbing codes.  Two of the leading code-writing bodies – the International Code Council (ICC) and the International Association of Plumbing and Mechanical Officials (IAPMO) have been considering changes for their respective versions of model codes that will be published in 2015.  Once published, these model codes take on the force of law when later adopted by state and local governments.  Taken together, the ICC and IAPMO codes are in effect in nearly every state in the nation.

Working with partners such as the Alliance to Save Energy, the American Council for an Energy-Efficient Economy, and leading hot water consultant Gary Klein, NRDC’s efforts led the ICC to recently approve some important changes for 2015. 

The ICC’s plumbing code will take some initial steps to reduce hot water waste.  A proposal authored by NRDC has been approved to remove obsolete requirements that encouraged oversizing of hot water piping leading to showers and sinks.  Even more significantly, the ICC’s energy code will require the insulation of nearly all hot water pipes in new commercial buildings and all hot water pipes with a diameter of ¾ inch or more in new residential buildings.  This is a major breakthrough, because the “spine” of most residential hot water distribution systems begins with ¾ inch pipe.  (The ICC approved other important energy-saving measures noted here by my colleague Meg Waltner.)

 Pipe insulation photo flickr.jpg                    Pipe insulation at a job site. (Photo Credit: Eva Ekeblad | Flickr)

Now attention turns to IAPMO, where the revision cycle for their 2015 codes is still in progress.  In this effort, NRDC is collaborating with the AFL-CIO affiliated professional plumbers union, the United Association of Journeymen and Apprentices of the Plumbing and Pipefitting Industry – the “UA” for short.  In early January, NRDC and the UA jointly proposed that IAPMO’s 2015 Uniform Plumbing Code include requirements to insulate all hot water piping in new commercial and residential buildings.  NRDC estimates that the joint proposal will reduce the waste of water and energy in new homes by 15 to 30%. 

The UA’s General President, George Hite, stated that: “Throughout the construction industry, there are untapped opportunities to make our buildings and our economy more efficient, and we should seize these opportunities to create good jobs for American workers.”  Peter Lehner, NRDC’s Executive Director, noted that: “This proposal will not only save homeowners and renters money on their utility bills, but it also protects our environment by cutting energy and water use.”

The NRDC-UA joint proposal for pipe insulation will be considered during the next meeting of IAPMO’s UPC Technical Committee which begins on April 28.  Final action will come in the Fall.  The full text of the proposal can be seen here.

With our partners and trade allies, NRDC will continue to explore additional strategies to reduce hot water wait time and waste, including more compact piping layouts and better placement of hot water heaters.  Meanwhile, a breakthrough on pipe insulation in the 2015 model building and plumbing codes can help ensure that new homes will no longer feature longer wait times and greater waste of hot water. 

How long do you wait for hot water? Take our web poll here and let us know.

Use your stopwatch app, and measure how long you actually wait for hot water.  You may be surprised!  Tell us what you do while you wait, and a little bit about the type and age of your building.  We'll share the results in an upcoming post.

Share | | |

Comments

Dave GrieshopJan 24 2014 07:09 PM

Great to see wasted water (and wasted energy) getting more attention in residences.
I had the pleasure of watching Gary Klein succeed at the last ICC round of code proposal changes. He won a bunch!
This topic in a report, in conjunction with Gary Klein, will be finished shortly that addresses this very issue. Suffice it to say 80% annual reductions in wasted water when using demand controlled pumps are being routinely experienced based on inputs in a constrained environment.

GuthrumJan 25 2014 08:19 AM

We used to play the waiting game. By insulating our hot water pipes in the crawl space, the wait time has been cut by 2/3. The cost was around $50 and took about three hours. All I needed was: insulation, utility knife, tape measure, and a good light. I am now looking for a recirculating pump to put at the water heater. I have read about those and saw a "This Old House" episode about those. When our water heater goes out, I will switch to a tankless. If people are building, remodeling, or replacing, they should look at tankless models. Another solution for some instances is the at-site water heater, which is small and would fit in a sink cabinet. This is a good solution in some cases.
One of the best systems is the furnace that heats the home and the hot water.These are very efficient. These have been around for some time, but are great.
I would like to hear from other people and their experiences.

Comments are closed for this post.

About

Switchboard is the staff blog of the Natural Resources Defense Council, the nation’s most effective environmental group. For more about our work, including in-depth policy documents, action alerts and ways you can contribute, visit NRDC.org.

Feeds: Ed Osann’s blog

Feeds: Stay Plugged In